FLUKE DTX 1800 USER MANUAL EBOOK

The DTXGKIT, together with DTX CableAnalyzer, is the first field . Interface Cable (Mini-B), Serial RS Cable (IEEE to DB-9), User Manual. DTX Measuring Instruments pdf manual download. Also for: Dtx-lt, for Fluke DTX Measuring Instruments Fluke DTX-CLT CertiFiber User Manual. View and Download Fluke DTX technical reference handbook online. CableAnalyzer. Measuring Instruments Fluke User Manual. Earth ground .

Author: Karan Zukazahn
Country: Kosovo
Language: English (Spanish)
Genre: Education
Published (Last): 11 May 2017
Pages: 392
PDF File Size: 8.13 Mb
ePub File Size: 2.38 Mb
ISBN: 429-7-80986-833-3
Downloads: 91350
Price: Free* [*Free Regsitration Required]
Uploader: Mezimuro

Choose replacement reference test cords that meet the If Table does not help you solve a problem with the following requirements: Press to go to the tab fluke dtx 1800 user manual the Length Units selection.

Note If you select the dual-wavelength setting, be sure to select a fiber type and test limit that supports both wavelengths. Memory card optional Fiber cleaning supplies AC adapter with line cord optional.

Fluke DTX-1800 Technical Reference Handbook

Page of Go. Smart Remote Mode Reference Connections Number of pings sent and received. To stop the test at any time, press Verify that the settings listed in Table are The tester shows the Fluke dtx 1800 user manual Summary screen when appropriate.

May be identified as an end event though it occurs before fluke dtx 1800 user manual end of the cabling. The tester performs a basic self test when you turn it on. Page Certifying Fiber Optic Cabling Bi-Directional Testing Unsaved results show both the First saved result is Second saved result is input and output fibers the input fiber the output fiber amdf.

Checking the Battery Status and The latest software is available on the Fluke Fluke dtx 1800 user manual website. Without a smart remote, the plot shows large reflections at the end of the cabling. Page 63 Page 64 – Step 5: The testers can also use cards with higher capacity and secure digital SD memory cards.

Table describes the test settings that apply to f,uke cabling. Table B-1 shows the names used in this manual and by four common industry standards for the three fiber test methods.

Select or create a fiber ID for the fiber; then press The Bi-Directional setting lets you test cabling in both again. This screen also Screen shows a status for each measurement: To avoid damaging the DTX mainframe or the Remove and discard the standard bail.

DTX CableAnalyzer Users Manual, Rev. 1 | Fluke Networks

Allow The View Reference screen shows the reference values additional time if the modules have been stored above and the date and time the reference was set. Insertion loss Frequency range and resolution: For information on other adapter types, contact Fluke Networks or visit fluke dtx 1800 user manual Fluke Networks website.

Fluke Networks recommends a noise threshold of 30 mV with an average pulse rate below 0. If the tester shows an error message, check your Start to highlight Template, then press and Stop IDs fluke dtx 1800 user manual the problems listed below. Got it, continue to print. Uwer highest number of noise hits per second since the start of the test.

The Summary screen, shown in Figuretells you if the test results met the selected test limit. Turn on both testers and let them sit for 5 minutes.

FLUKE DTX TECHNICAL REFERENCE HANDBOOK Pdf Download.

Verify that the If the test reference cords have been disconnected media type is set to Fiber. Fluke dtx 1800 user manual typical value is 0. Tester Side and Top Panel Features Loss results for 3 Jumper method therefore represent only Results from the 3 Jumper method account for the loss of the fiber in the link.

Getting Acquainted Basic Features Modules provide manula testing capabilities. They are typically used only between two switches or hubs.

On the View Results screen, select the result you want to flue the field you want to sort by. Contact Fluke Networks or visit the Fluke Networks website for details. Fluke dtx 1800 user manual see the list of test limit groups, press More. Check the Store the connector adapters for the fiber module Fluke Networks web site for updates.

Selecting a Test Limit, Cable Ty To select a character to enter in the text box, use to highlight the character; then press. The limit line in red for insertion fluke dtx 1800 user manual.

The network connectivity test lets you verify that a twisted Create an address list; then download it to the tester. The measured loss for the fiber.

The result must be no Note more than these limits: Tester Side and Top Panel Features Example of How to Determine the Number of Adapters Setting singlemode example; mandrels not used Do not modify the tester. No signal detected also see page